Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Fern Park, FL
Gate installation in Fern Park usually means replacing a 60-year-old swing gate that’s been repaired one too many times, or adding automation to a driveway gate on a mid-century ranch home. Regent Gate Repair has served Fern Park since 2013, and most of our install work here is on homes built between the 1950s and 1970s where the original posts have settled in sandy soil and the hardware is simply done. We quote the full job before we start, and we handle everything from pulling the old gate to programming the new opener. Call (855) 927-1091 for a free estimate.
Why Fern Park Homes Are Different
Fern Park is a compact, mostly built-out pocket of Seminole County sitting between Winter Park and Casselberry along US 17-92. The housing stock here skews heavily toward 1950s-to-1970s ranch and block-stucco homes on generous lots, which means the gates we see are almost all residential: driveway swing gates, rear property-line gates, and fenced-yard entries that were added piecemeal over decades. A lot of that hardware was undersized from day one, and the original 4×4 gate posts were set in the sandy, fast-draining soil that defines this area.
That soil matters more than people think. After heavy summer rain, old posts lean and settle, and a Fern Park gate that won’t latch is often a footing problem, not a hinge problem. Add Central Florida’s humidity and lightning, and operators take a beating while hinges rust from the inside out. Hurricane-season wind loads bend gates enough to throw off opener alignment. When we do an installation here, we plan for these conditions: bigger posts, deeper footings, and operators rated for moisture and surge. A gate installed right in Fern Park starts with knowing what 60 years of Florida weather has already done to the site.
Styles & brands we work with
Our Main Fern Park Services
Fern Park homeowners call us most about two things: a gate that stopped working, and a gate that needs automation or replacement. Both live under one roof here.
Gate Repair in Fern Park
Most repair calls in Fern Park start with a gate that drags, won’t latch, or swings crooked after a storm. The homes here are old enough that we regularly find rusted hinges, sagging posts, and operators that predate modern safety sensors. We rebuild, re-anchor, and re-align before recommending replacement. Gate Repair in Fern Park covers everything from a stuck roller to a full operator swap.
Electric Gate Repair in Fern Park
Lightning is hard on gate electronics in this part of Seminole County. We get calls after summer storms for dead control boards, blown fuses, and safety sensors knocked out of alignment. If your gate opens but won’t close, or the remote stopped working overnight, that’s electric gate work, not just mechanical. Electric Gate Repair in Fern Park covers the wiring, boards, loop detectors, and remotes.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Fern Park
Gate installation in Fern Park typically costs $1,600 to $4,800 for a single residential swing gate with a new operator. Most of the homes here were built in the 1950s through 1970s, so we’re usually removing a gate that’s been patched for decades and replacing it with new posts, new hardware, and an automated opener sized for how the gate actually gets used. You’ll pay the price we quote before we order anything. For a full look at what’s involved, see our Gate Installation service page.
Automatic Gate Installation
Signs you need it
You’re getting out of the car twice a day to open and close a driveway gate by hand, or the old opener fails more than it works.
What it costs in Fern Park
Automatic gate installation in Fern Park runs $2,000 to $4,800 for a single swing gate including the operator, arms, safety sensors, and remotes.
How we do it
We set or shore the posts, mount the operator and arms, run the low-voltage power, install the safety sensors, and program your remotes before we leave.
Driveway Gate Installation
Signs you need it
The existing driveway gate has rusted through at the hinge mounts, or the posts have sunk far enough in sandy soil that the gate no longer clears the ground.
What it costs in Fern Park
A new driveway swing gate in Fern Park is $2,500 to $5,500 installed, depending on width, material, and whether we’re reusing your existing motor.
How we do it
We dig new post footings below the sandy topsoil, set steel posts, hang and square the gate, then install or transfer the operator and set the travel limits.
Sliding Gate Installation
Signs you need it
Your lot slopes toward the driveway and a swing gate binds on the grade, or you don’t have room for a swing gate to arc open.
What it costs in Fern Park
Sliding gate installation in Fern Park runs $3,500 to $6,000, which includes the track, the gate, the operator, and the safety photo eyes.
How we do it
We pour a level concrete track pad, set the gate on its rollers, mount the rack and operator, then wire and test the safety edges.
What Gate Installation Costs in Fern Park
| Item | Typical range in Fern Park |
|---|---|
| Single swing gate with automation | $1,600 – $6,000 |
| Sliding gate with operator | $3,500 – $6,000 |
| Automatic gate installation (labor + motor) | $2,000 – $4,800 |
Can you install a gate on an old Fern Park home’s existing posts?
Sometimes, but we won’t promise it until we see the footings. Posts set in Fern Park’s sandy soil in the 1960s are often undersized and leaning, and hanging a new automated gate on a weak post guarantees an early failure. We’ll tell you honestly whether the posts can be shored or need replacing. Call (855) 927-1091 and we’ll come look.
Do you handle the electrical work for an automated gate in Fern Park?
Yes. We run the low-voltage power to the operator, wire the safety sensors and keypad, and set up remotes. The gate is automated and tested before we leave, so you don’t need to call an electrician separately.
Brands We Service in Fern Park
We work on LiftMaster, FAAC, BFT, and Linear operators daily in Fern Park, and we keep common control boards, remotes, and safety sensors on our trucks for these brands. That means many calls are fixed in one visit instead of two. We pull from our full brand lineup on our our brands page.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Fern Park, FL
| Service | Typical range in Fern Park |
|---|---|
| Gate repair (general) | $125 – $850 |
| Electric gate repair | $200 – $1,000 |
| Gate installation (single swing) | $1,600 – $6,000 |
| Automatic gate installation | $2,000 – $4,800 |
| Driveway gate installation | $2,500 – $5,500 |
| Sliding gate installation | $3,500 – $6,000 |
Prices in Fern Park push higher when we’re re-anchoring posts set in old sandy footings, or when an older home needs new low-voltage wire run to the operator. Whatever the number, you’ll get it in writing before any work begins, and it won’t change unless we find something structural and talk to you first.
Neighborhoods We Serve in Fern Park
Fern Park is small enough that we cover the whole 32730 ZIP without splitting it into far-flung zones. Most calls come from the mid-century ranches off US 17-92 and the side streets east toward Casselberry.
- The neighborhoods along Oxford Road and the residential streets west of 17-92
- The block-stucco ranch pockets south toward Winter Park
- The streets running east of 17-92 toward the Casselberry line
- The older lots near the Seminole County line north of the 436 corridor
We can usually reach any Fern Park address the same day you call for repair work.
Service Area – Cities Near Fern Park
Regent Gate Repair covers Fern Park and the surrounding Seminole County communities. We also work regularly in Maitland, FL, Altamonte Springs, FL, Eatonville, FL, and Casselberry, FL. If you’re on the edge of 32730 and not sure whether we cover you, call and ask.
Serving Fern Park, FL — Our Local Coverage Area
We’re based in the Fern Park area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Fern Park
For repair calls in Fern Park, we can usually arrive the same day, often within a couple of hours. Installation work is scheduled, but we’ll give you a firm date when we quote the job. Call (855) 927-1091 to check today’s availability.
Most residential gate replacements and repairs don’t require a permit in Seminole County, but if a new installation involves electrical work or sits on a corner lot with sight-line rules, it’s worth confirming. We’ll flag any concerns during the estimate, and we handle the details you don’t want to chase down.
Absolutely. That’s most of what we see in Fern Park. Whether the gate is wrought iron, chain link, or wood on original masonry posts, we’ll assess the hardware, the post condition, and the operator, then tell you what’s worth saving and what should be replaced.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Fern Park Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Jeff Ackerman"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
— Daniel Novak"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
— Cole Mercer