Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Edgewater, FL
Gate installation in Edgewater usually runs $1,850 to $6,500 for a complete automated driveway gate, depending on gate width, material, and operator brand. Most Edgewater jobs we quote involve replacing a salt-corroded or storm-damaged gate, or adding an electric opener to an existing manual gate on a canal-front or near-water property. We’re Regent Gate Repair, a gate-only company, and we handle every part of the job from the post to the control board. Call (855) 927-1091 for a free measure and a written quote before any work starts.
Why Edgewater Homes Are Different
Edgewater sits between the Indian River Lagoon and Mosquito Lagoon, and that location shapes every gate we touch here. A large share of homes in 32141 are canal-front or within a few blocks of salt water, which means gate hardware lives in salt-laden onshore air almost year-round. Steel hinges, latch springs, and operator arms rust fast. Aluminum fares better but still suffers pitting at welds and fastener points if not treated. It changes what we stock on the truck and what we recommend for replacement parts, which is stainless or powder-coated hardware instead of raw steel.
The housing stock compounds this. Edgewater is mostly single-story concrete-block and wood-frame homes from the 1960s through the 2000s. Older lots commonly have wood picket or chain-link gates, many of them original to the house. Newer builds off Parkton Road and in the western subdivisions trend toward aluminum and vinyl driveway gates. Each fails differently in this climate. Wood warps and rots at the bottom rail where sprinkler overspray and humidity sit. Chain-link hinges seize. Aluminum gates hold up structurally but their automation systems, control boards and limit switches especially, suffer in the humidity and afternoon thunderstorms that roll through from spring into fall.
Storm season is the other edge Edgewater lives on. Tropical systems and even routine squalls knock unbraced gates off their posts, loosen cantilever rollers, and short out exposed operator wiring. When we install a gate in Edgewater, we plan for wind load and for salt. That means heavier posts, through-bolted hinges, sealed control boxes, and dielectric grease on every electrical connection. A gate built for inland Florida will fail here in two or three seasons.
Styles & brands we work with
Our Main Edgewater Services
Edgewater homeowners call us for two things most often: a gate that won’t open or close correctly, and an electric system that stopped responding. Each service has its own Edgewater page, linked below.
Gate Repair in Edgewater
Mechanical gate repair in Edgewater means fixing what salt air and storms do to the physical gate. We replace seized hinges, rebuild sagging wood picket gates, reset posts that have pulled out of sandy river-adjacent soil, and align gates that no longer latch after a storm shifted the frame. In the canal-front neighborhoods off the river, hinges and latches routinely seize from salt corrosion within a season or two, so we keep penetrating oil and stainless replacement hardware on the truck as a standard call item. For the full scope of what we repair, see our Gate Repair in Edgewater page.
Electric Gate Repair in Edgewater
Electric gate repair in Edgewater covers the operator and everything connected to it: control boards, loop detectors, photo eyes, keypads, remotes, and the low-voltage wiring that humidity and salt corrode. Most Edgewater service calls in 32132 and 32141 involve a gate that won’t respond to a remote, a gate that opens but won’t close, or an operator that hums but won’t move the gate. We diagnose brand-specific failure patterns on LiftMaster, FAAC, and Linear systems rather than guessing. Details on this service are on our Electric Gate Repair in Edgewater page.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Edgewater
New gate installation in Edgewater solves the two problems this climate creates again and again: a salt-corroded or storm-battered gate that isn’t worth another repair, and a manual gate the owner now wants automated. Because Edgewater is dominated by canal-front and near-water homes, we size every new gate and operator for wind load and salt exposure, not just for the opening width. We install the gate and the automation, handle the low-voltage wiring, and set the safety edges and photo sensors. The same crew that repairs gates also installs them, so if a repair turns out to be a lost cause, you don’t need a second contractor. That’s the core of our Gate Installation service.
Automatic Gate Installation
Signs you need it
You’re opening and closing your driveway gate by hand every day, or the gate has no opener at all and you want keypad or remote access instead of getting out of the car.
What it costs in Edgewater
Automatic gate installation in Edgewater typically runs $2,800 to $6,500, with the operator itself adding $950 to $2,800 depending on brand and duty cycle.
How we do it
We set or reinforce the gate posts, mount the operator arm or underground unit, pull the low-voltage power run, and program the board, remotes, and safety loops, then test the full cycle at least twenty times before we leave.
Driveway Gate Installation
Signs you need it
Your existing driveway gate is storm-damaged, rotted at the rails, or sagging badly enough that repair would cost more than replacing the gate and post hardware.
What it costs in Edgewater
A new driveway gate in Edgewater runs $1,850 to $4,800 for the gate, with automation adding $950 to $2,800 when an opener is included.
How we do it
We measure the opening and grade, set posts in concrete sized for the wind load Edgewater sees, hang the gate with through-bolted stainless hinges, and if the job includes automation, pull the power and program the full system.
Sliding Gate Installation
Signs you need it
Your lot drains toward the gate or your driveway slopes into the opening, so a swing gate would drag or bind, or you have a wide opening a swing gate can’t span cleanly.
What it costs in Edgewater
Sliding gate installation in Edgewater typically runs $3,200 to $7,800, with the higher end covering commercial-grade operators and longer cantilever spans.
How we do it
We pour and anchor the track or set the cantilever rollers, hang the gate, mount the operator and rack, and then wire and test the safety edges and photo sensors on both ends of travel.
Electric Gate Installation
Signs you need it
You have a manual gate that’s structurally fine, but you want keypad entry, remote control, or integration with an intercom or access control system on a canal-front or near-water home.
What it costs in Edgewater
Electric gate installation on an existing manual gate runs $1,200 to $2,900 for the operator and wiring, exclusive of any gate repairs needed before the opener goes on.
How we do it
We mount the operator, pull the low-voltage and line-voltage runs in sealed conduit, install the safety edges and photo eyes, and program remotes and keypads, then test the obstruction reversal and auto-close settings.
What Gate Installation Costs in Edgewater
| Item | Typical range in Edgewater |
|---|---|
| Driveway gate (swing, aluminum or steel) | $1,850 – $4,800 |
| Gate operator (added to gate) | $950 – $2,800 |
| Sliding gate system with operator | $3,200 – $7,800 |
Does a new gate in Edgewater include the power run?
Yes. Every electric gate installation we do in Edgewater includes the low-voltage wiring and any line-voltage run needed to power the operator, run in sealed conduit to handle humidity and afternoon storms. The price is quoted before work starts, and nothing extra gets added to the invoice later.
Can you replace a salt-corroded gate without replacing the posts?
Sometimes. If the existing posts are concrete-set and still plumb, we can hang a new gate on them and replace the hinges and latches with stainless hardware. If the posts are rusted at grade or shifted, replacement posts are the only fix that will last. Call (855) 927-1091 for a free measure and an exact quote.
Brands We Service in Edgewater
We work on LiftMaster, FAAC, BFT, and Linear operators across Edgewater. Our trucks carry common boards, limit switches, and remote receivers for these brands, so a single visit usually gets a diagnosis and the repair done. For the full list of what we service, see our brands.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Edgewater, FL
| Service | Typical range in Edgewater |
|---|---|
| Gate repair (labor) | $75 – $189 |
| Gate repair (labor and parts) | $120 – $450 |
| Electric gate repair (labor and parts) | $150 – $650 |
| Gate opener repair (labor and parts) | $120 – $400 |
| Driveway gate (new, swing) | $1,850 – $4,800 |
| Gate operator (added to gate) | $950 – $2,800 |
| Sliding gate system with operator | $3,200 – $7,800 |
| Electric gate installation (existing gate) | $1,200 – $2,900 |
Prices in Edgewater climb when a job involves salt-corroded hardware that has to be cut out rather than unbolted, or when a gate near the river needs stainless replacements and extra bracing for wind load. Every job is quoted and agreed before we start work, so the price on the quote is the price on the invoice.
Neighborhoods We Serve in Edgewater
We work across Edgewater and the surrounding area, from canal-front streets off the Indian River to newer subdivisions west of I-95. We typically reach Edgewater jobs the same day for repair calls, and we schedule installations for a measure and written quote at your first call.
- Edgewater canal-front neighborhoods (32141)
- Parkton Road area
- West Edgewater subdivisions (32132)
- Near Cow Creek
- Florida Shores
Service Area – Cities Near Edgewater
Beyond Edgewater, we run service calls into the neighboring coastal and river communities. Homeowners in New Smyrna Beach, FL face the same salt-air gate failures we see in Edgewater, while Glencoe, FL and Oak Hill, FL keep us busy with storm-damaged and aging manual gates. We also cover Ponce Inlet, FL for both residential and commercial gate work. Call (855) 927-1091 for service anywhere in the area.
Serving Edgewater, FL — Our Local Coverage Area
We’re based in the Edgewater area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Edgewater
For repair calls, we usually reach Edgewater properties the same day, often within a few hours for urgent failures like a gate stuck open or an operator that won’t respond. Installation work is scheduled for a free measure first, then a written quote and a set install date. Call (855) 927-1091 and we’ll tell you exactly when we can be there.
Permit rules in Edgewater depend on the scope: a gate-only replacement on existing posts usually needs no permit, while new posts, electrical runs, or a new operator can require one. We’ll identify what’s needed for your specific property during the free measure, and we handle the paperwork as part of the installation.
Yes, and they’re a regular part of our work since so much of Edgewater sits on the Indian River Lagoon and Mosquito Lagoon. We use stainless hardware, sealed control boxes, and corrosion-resistant fasteners as standard on canal-front jobs, because salt air eats raw steel hinges and latches within a season or two. Call (855) 927-1091 for a free estimate.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Edgewater Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
— Roger Barrett"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
— Diego Mendoza"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
— Anika Patel